# LDLS — running somebody else's drivers SchOS cannot write a driver for every device that exists. No project can. The only route to the hardware support an established system has is to run Linux's drivers, and LDLS is what does that. It works, and on more than one driver. `8139too` and `e1000` — unmodified GPL kernel modules — load into a SchOS process, drive their hardware through `/dev/pci`, and carry packets (both under QEMU). A third, Linux's `r8169`, is the NIC driver on the ASUS TUF A15 laptop, and it is the first that needs a *set* of modules and not one; it is described under *A set of modules*. It has registered its interface and read its PHY on that laptop; whether it carries traffic there has not been confirmed yet. ``` # ldlsd /lib/modules/8139too.ko /lib/modules/btf & kpi: the driver read a MAC off the hardware: 52:54:00:ab:cd:ef ndo_open returned 0 carrying frames. the interface is ldls0. # ping 10.9.0.2 4 64 bytes from 10.9.0.2: icmp_seq=1 time=30 ms ... 4 packets transmitted, 4 received, 0% packet loss ``` `10.9.0.0/24` is reachable only through `ldls0`. The address on it came from DHCP, over the same driver. The e1000 run is the more interesting of the two, because it is a **handover**: the kernel was driving that NIC, and gave it up. ``` net: eth1 is gone; interface 1 removed e1000: released to userspace; the interface is down rehomed 23 %gs per-CPU reference(s) calling probe, with 82 of 155 symbols implemented kpi: the driver read a MAC off the hardware: 52:54:00:12:34:57 net: ldls0 attached as interface 2, asking for an address net: ldls0 10.9.0.15/255.255.255.0 via 10.9.0.2 ``` Everything the second driver needed that the first did not is below, and the pattern in it is worth naming up front: **none of it was a missing feature.** Every one was a call that succeeded, returned zero, and did nothing. --- ## The rules it is built on Five, and everything else is an implementation of them. ### 1. Linux code may ship; so far the tree holds none This rule used to say nothing GPL would ever enter an image we build. It was a policy, never a licence constraint — SchOS is GPL-2.0-or-later, and GPL-2.0-only code combines with it — and the owner has overridden it: **Linux code and firmware blobs may be shipped.** What survives of the rule is mechanical, not legal. The repository carries no `*.ko` (`.gitignore` refuses them), and `make ldls-stage KO=…` / `make ldls-r8169` stage modules into a *local* image from the Linux kernel on the build machine, because a module, its dependencies and the BTF that describes them have to come from the same Linux build and that kernel is the easiest place to get a matching set. Shipping one is therefore a decision about the release, not about the code: an ISO that contains `r8169.ko` is a distribution of GPL-2.0-only code and carries the usual obligation — its source goes with it — see [../licensing.md](../licensing.md) §6. ### 2. It runs in a process, never in the kernel A module linked into our kernel is the strongest derivative-work argument that exists. A module combined with our shim inside a user process is a different thing at arm's length — the position FreeBSD has shipped from for a decade. And practically: this is foreign code. A driver we did not write, cannot fully audit and did not choose the quality of should not be able to take the machine down. ### 3. Facts, not expression A symbol's signature and a struct's field offsets are facts a compiled driver depends on. Comments, macro bodies and implementations are expression and are never carried over. Every file in `ldls/kpi/` records where its shape came from. Mostly the question does not arise, because of rule 3½: ### 3½. The layouts are not in our source at all A kernel built with `CONFIG_DEBUG_INFO_BTF` publishes `/sys/kernel/btf/vmlinux`: every struct layout and every function prototype, as generated type data describing the kernel that is installed. `ldls/btf.c` reads it at load time, on the user's machine, from the user's own kernel. ``` $ ldls-types /sys/kernel/btf/vmlinux --need pci_driver probe offset 16 size 8 pci_dev resource offset 1000 size 1088 resource start offset 0 size 8 all present ``` Nothing there is ours to have transcribed, and it is right for the kernel actually present rather than one pinned by guessing. ### 4. One kernel version at a time Linux states in writing that it has no stable in-kernel ABI. BTF mostly dissolves this, because it describes the kernel that is there — but a kernel without BTF needs hand-written layouts for a named version, and that is when this rule bites. ### 5. The unresolved-symbol list is the specification Do not guess the API surface. Load a real module and let the loader say what is missing. Every symbol LDLS does not implement still *resolves*, to a stub that reports itself and returns zero, so the driver carries on and the next thing it wants becomes visible. The work queue keeps writing itself. --- ## The four pieces ### The loader — `ldls/ko.c` A `.ko` is an ELF64 relocatable object. Index the sections, place the allocatable ones, resolve the undefined symbols, apply the relocations. Written from the ELF-64 gABI and the x86-64 psABI, both published specifications, so there is no licence question in it at all. Measured over a stock 6.18.46 tree: **2,440 modules, every one lays out and relocates to completion**, five relocation types, nothing unhandled. That sweep is also what retired the fixed section table — `nvidia-modeset` has 7,069 sections against a median of 50 — so the caller supplies it and there is no limit to run into. It is **freestanding**: no libc, no allocation, no I/O. The same source builds as a host tool, where a format failure costs a second, and as the SchOS-side host. That is the arrangement `mkschfs` and the kernel already share. #### Three things it has to fix in the object **The `%gs` stack guard.** Modules are built `-mstack-protector-guard-reg=gs`, so the canary is fetched through the GS segment — an ABI between the kernel and its own per-CPU area that a host which is not that kernel cannot provide. `ko_defuse_gs()` rewrites those references to `xor %reg, %reg`. There are two forms: the prologue *loads* the guard with `mov`, the epilogue *compares* it with `sub` before a `jne`. `xor` is right for both — it zeroes the canary and sets ZF, so the branch falls through as a passing check does. It checks every site before patching any and refuses the whole operation on anything it does not recognise. **Every other per-CPU variable.** The guard turned out to be one instance of a general problem. `current` is another — `mov %gs:const_current_task(%rip), %r8` — and e1000 has 23 such references across four variables. Defusing does not work here: the guard's *value* is arbitrary, and `current`'s is not, because the driver dereferences what it reads. What does work is that **a per-CPU variable in a single-threaded host is just a variable**. `ko_fixup_percpu()` takes the `%gs` off, leaving the same opcode reading the same width in the same direction, from storage the host supplies per name. Eight bytes become seven and a `nop`. The displacement is measured from the end of the *shortened* instruction, and the displacement is not always last — `cmpb $0x0, %gs:softnet_data+0x75(%rip)` has an immediate after it — so there is just enough of an x86 decoder in there to know how long the instruction is. Anything it does not recognise is refused with the symbol named, which is rule 5 again. `ldlsd` hands out zeroed blobs, except for `current`, which points at the rest of its own: a driver that walks into the task it thinks it has reads zeroes. **The compiler's thunks.** `__x86_indirect_thunk_rN` and `__x86_return_thunk` are retpolines, not API, and they are pure control flow — `jmp *%r8` and `ret`. A stub cannot stand in for one, because a stub's whole behaviour is to log a name and return, and what a thunk is *for* is the jump. `ldls/kpi/thunk.c` is fifteen lines of assembly and is the single highest-value file in the layer. That one cost a day. e1000 refills its receive ring through a function pointer and the compiler made it a *tail* call: ``` mov 0x2a0(%rbx),%r8 ; adapter->alloc_rx_buf ... ; compute E1000_DESC_UNUSED(ring) == 255 jmp __x86_indirect_thunk_r8 ``` so the driver asked for 255 receive buffers, the shim answered "yes", and the symptom was a NIC that transmitted perfectly and received nothing with `RDT` sitting at zero. **Where it is loaded.** `-mcmodel=kernel` means `R_X86_64_32S` relocations, so the object has to live where a signed 32-bit absolute address reaches. A process's mmap area starts at `0x40000000`, which is inside that window; on the host harness `MAP_32BIT` reaches it from the other end. ### A set of modules — what r8169 needed Linux's `r8169` is not one module. It needs `mdio-bus`, `libphy`, `mdio_devres`, the Realtek PHY driver, the NIC itself, the RTL PHY firmware, and the BTF of the kernel they came from. `make ldls-r8169` stages all of that from the running kernel; `etc/schinit/ldls-r8169.job` starts `ldlsd` on it at boot, with its output in `/var/log/ldls-r8169.log`. The job has `KeepAlive = no`: a driver that crashes on real hardware would otherwise be restarted into the same crash every few seconds. What that added to `ldlsd`: - **A comma-separated module set**, loaded in dependency order, each linking against the ones before it, with the BTF read before any `init_module` runs. A library module (`libphy`) just exports symbols to the next; the PCI `probe` runs once, at the end, for whichever module registered a `pci_driver`. - **A driver core**: bus match, driver probe, so the PHY driver binds to the PHY the way it does in Linux; **devres**; a kernel `printf`; real `udelay`/`msleep`/ `ktime`; and **1000 Hz `jiffies`**, because the module's `HZ` is compiled in and phylib re-arms its link poll `HZ` jiffies out. - **Firmware** read from `/lib/firmware`. - **phylib's data**, the `link_mode_params` table and its bitmaps. - **The symbols whose stub-zero was a lie**: list validity, `try_module_get`, `dev_err_probe`, `eth_platform_get_mac_address`, `napi_consume_skb` (as a stub it leaked one buffer per transmitted frame until the DMA heap ran out), and the rest of the table at the end of this document. - `pdev->bus` is a real `pci_bus`; `net_device.priv_len` is set from BTF (the driver's `memset` of its ring bookkeeping is bounds-checked against it, and `__fortify_panic` fired on a length of zero); and `cmovcc` from per-CPU memory is rewritten like the other `%gs` forms. - **`__preempt_count` starts at `PREEMPT_ENABLED`.** mdio-bus keeps the register it has just read in `r11` across `preempt_enable()`, which on x86 is `decl %gs:__preempt_count; je`, to a call that preserves every register. With the count at zero the call was made, into a logging stub whose syscall left `RFLAGS` (0x246) in `r11` — so every MDIO read returned `0x02460246`. `preempt_schedule` is now a bare `ret`. - `__fortify_panic` names the module and function (`r8169: rtl_open.cold+0x…`) so a photograph of the screen is enough, and exits instead of spinning on a core and holding `/dev/netdev`. The kernel did two things for it. It turns **ASPM off on Realtek NIC links** at boot, as `r8169` does through `pci_disable_link_state`, which a process cannot; and a network interface that **appears after boot starts the stack** — with the native driver out of the registry the laptop boots with no interface at all, and `ldls0` arrives later. `ldlsd` says which refusal it got when attaching: `EBUSY` is another process, anything else is the kernel. The native `drivers/net/r8169/` stays in the tree, with Linux's 8168H setup, as the fallback; it is out of the registry. ### The KPI — `ldls/kpi/` The Linux symbols, implemented. Register access to a mapped BAR; the PCI calls to `/dev/pci`; allocation to `mmap` and `PCIIOC_DMA`; `register_netdev` to `/dev/netdev`. Organised under Linux's own header names so a reader who knows where something lives in Linux knows where it is here. `kpi_io_ok()` bounds every `ioread`/`iowrite` against the mapping `pci_iomap` returned. A stray access would otherwise be a page fault with no context, and with no IOMMU a hosted driver's wild writes have to be caught early or not at all. Three pieces of it are not register access and are worth naming, because each one is something a driver does that a poll loop does not obviously provide: - **The interrupt handler runs.** Not to receive packets — LDLS was already calling the NAPI poll by hand — but because a driver's handler is where it does everything *else*. e1000 queues its watchdog from there, and the watchdog is what sets `TCTL.EN`. A driver whose handler never ran was a driver whose transmitter was never switched on. Calling it from the loop is safe: a handler's first act is to read its cause register, and with nothing pending it returns `IRQ_NONE`. - **Deferred work runs.** `queue_delayed_work_on` keeps the item and `kpi_work_run()` calls what is due from the same loop. `jiffies` had to start moving for that to mean anything; it comes from `uptime()`, at 100 Hz. - **`netif_carrier_on`/`off` write the bit.** `netif_carrier_ok()` is an inline that tests `__LINK_STATE_NOCARRIER` in `net_device.state`, so a no-op means the driver reads "the carrier is already up" and skips its whole link-up path. The bit number comes from the kernel's BTF (`btf_enum_value()`), not from us — rule 3½ applied to a constant rather than an offset. And **DMA in small pieces**. `dma_alloc_coherent` maps onto `PCIIOC_DMA` exactly; `dma_map_single` does not. 8139too never needed it, because it copies each frame into a ring it allocated coherently up front; e1000 hands the device individual buffers. Since a process cannot know the physical address of an ordinary page, those buffers come from the arena too, a chunk at a time behind a bump pointer. The address arithmetic for that is not a call at all. `dma_map_single` is a static inline, so what reaches the shim is already expanded: the module computes `pa = va - page_offset_base`, then `page = vmemmap_base + (pa >> 12) * 64`. Both bases are undefined *data* symbols — which means LDLS supplies them, and setting both to zero makes the whole thing reversible with no lookup table. ### The back end — `/dev/pci` Already built, for `vgpud`, before any of this existed. The design insisted the interface be about *PCI devices* rather than about a driver model, on the argument that an interface whose first consumers are native drivers is a general mechanism rather than a hole shaped like something foreign. A Linux driver's `pci_iomap`, `dma_alloc_coherent` and `request_irq` land on it unaltered, which is that argument being collected. ### Giving a device up — `release` A driver in the kernel has a `release` hook, and `/dev/pci` calls it before handing its device to a process. The honest answer to "may I have the one you are using" was *no* until a driver could be told to let go; e1000 is the first that can. Letting go is three things, and the third was missed at first: 1. quiesce the hardware — mask interrupts, clear `RCTL` and `TCTL`; 2. **mask the interrupt line.** The kernel's handler is gone and the device is about to be brought up by a driver in a process, so nothing will acknowledge the cause. The console said what that looks like: `irq 11: 449905 interrupts/second -- a device on this line is not acknowledging it`. It comes back when the process asks for it with `PCIIOC_IRQ`. 3. **take the interface out of the stack.** `net_detach()` is the missing half of `net_attach_late()`, and it went missing because nothing had ever taken a device back. An interface left behind keeps its address and the route to its subnet, so the stack goes on choosing it, and every frame reaches a `transmit` that now correctly refuses. Packets stop and nothing reports an error — which is indistinguishable from a driver in a process that does not work, and was mistaken for exactly that. ### Ports — the TSS I/O permission bitmap A Linux driver does not always ask. `ioread32` is a call the KPI can implement; `outl` is an *instruction* compiled into the module, and e1000's reset path picks it deliberately — "these controllers can't ack the 64-bit write when issuing the reset, so use IO-mapping as a workaround". On QEMU's 82540EM there is no route to a working NIC that avoids it. So a process holding a device gets that device's I/O BARs, **and no other ports**. x86 offers two ways to grant this and they are far apart: `IOPL=3` is one flag and hands over all 65536 ports, including the interrupt controller, the timer and the disk; the TSS I/O permission bitmap is per port. A foreign driver already has DMA with no IOMMU, and the answer to "this is not a security boundary" is not to move it further — so it is the bitmap, at 8 KB per CPU of resident memory. See [../../include/ioperm.h](../../include/ioperm.h). Writing it found a latent hole. The TSS's I/O map base is at offset 102 and the old code wrote offset 64; the field it meant to set stayed 0, and a base of 0 with a limit of `0x67` does not mean "no bitmap" — it means the bitmap starts at the top of the TSS. The CPU had been checking ports 0–831 against the TSS's own bytes, which are `RSP0`: a kernel stack pointer whose zero bits are permission. ### The class bridge — `/dev/netdev` The one piece the kernel had to grow. `netdev_ops` is four entries — `transmit`, `receive`, `mac`, `link_up` — so a process claims the device, supplies a MAC, and `read()`/`write()` carry the frames. `/dev/pci` with the arrows reversed: that hands a device *to* a process, this lets a process *be* one. See [devices.md](devices.md). lwIP never learns that the thing behind the vtable is not a driver. --- ## What it costs **It polls.** A Linux driver expects its interrupt handler to be called from an interrupt. `/dev/pci` does deliver them — by blocking `read()`, which needs a thread `ldlsd` does not have — so the handler, the NAPI poll and the driver's deferred work are all called from one loop instead. The same work, in a context LDLS can provide, at the cost of latency and a spinning process. **The stack protector is gone**, per `ko_defuse_gs()` above, and so are the retpolines, per `thunk.c`. Foreign code, no IOMMU, three hardening measures fewer. **Per-CPU means per-process.** Correct with one thread, and it is the same assumption as the no-op locks below, arrived at from the other side. **A lock is a no-op.** In one process with no preemption inside the driver there is nobody to race with. That is correct right up until a driver has an interrupt thread, and it is the deepest unfixed assumption in the layer. --- ## It can be killed The whole H2 machinery applies to a foreign driver unchanged, which was the point of having built it against our own: | | | |---|---| | `ldlsd` running | `ping` works; it holds the device and two DMA blocks | | killed | interface **down**, device released, bus mastering cleared, **DMA reclaimed** | | `ping` | fails honestly — `sendto: -5` | | a second `ldlsd` | `ping` works again, and the arena hands back the same addresses | `pciuser_release_all()` and `netuser_release_all()` sit beside each other in `exit()` for the same reason: a process holding a device is one that may crash. --- ## What it does not do - **Three drivers, one kernel version.** `8139too` and `e1000` on 6.18.46 against QEMU, and `r8169` on that version against QEMU (where it finds no device) and on one laptop (where it gets as far as the PHY). The second driver was worth more than the first: it found the per-CPU problem, the retpoline problem, the port-I/O problem, the interrupt storm and a seven-year-old hole in the TSS. Nothing here has been tried on a second kernel, and "LDLS runs Linux drivers" is still a claim about a category from a sample of three. - **No interrupts**, per the polling note above. - **`jiffies` assumes `HZ` is 1000**, which is what the kernels LDLS loads from are built with (`ldls_load.hz` can say otherwise). It comes from the monotonic clock in milliseconds. - **One work item at a time, on the main loop.** A driver whose deferred work blocks stops everything, including the transmit path it is probably waiting for. - **It is not a security boundary, and here that is worse than usual.** There is no IOMMU, so a hosted driver can point its device at any physical address. For SchOS's own drivers that isolates bugs and not intent; for *foreign* drivers the distinction between bug and intent is one we are in no position to make. This is the strongest argument for an IOMMU the project has produced. - **It relies on SchOS having no NX.** Every mapping is executable because `EFER.NXE` is never set. If that is ever fixed — and it should be — `ldlsd` needs a way to ask for executable memory, and `mmap` does not offer one. - **Nothing is ever freed.** A hosted driver's allocations last as long as the process, which is a leak in the strict sense and the right trade for a program that will be killed to restart it. - **BTF has to come from somewhere.** SchOS has no `/sys/kernel/btf/vmlinux`, so `make ldls-stage` / `ldls-r8169` copy it from the Linux kernel the module came from. A kernel built without `CONFIG_DEBUG_INFO_BTF` has neither. - **There is address-space groundwork nothing uses.** `kernel/arch/x86_64/vm.c` maps the kernel image a second time at `LDLS_KALIAS`, in the top 2 GB where a `-mcmodel=kernel` module can reach, with a `vmemmap` and a module area beside it — at every boot — and `include/ldls/ldls.h` describes a `/dev/ldls` control channel to load modules into the kernel. That was the start of an in-kernel loader, contradicting rule 2. Nothing calls either, and it should be finished as a decision or deleted. - **No config-space writes.** `/dev/pci` has none, deliberately — a write is how a BAR gets moved out from under the kernel — so a driver that needs one is refused loudly rather than quietly succeeded. - **No sysfs and no unload.** Modules depend on each other and firmware is read from `/lib/firmware`, but `module_exit` is never called, and the way to stop a driver is to kill the process. - **Some symbols are still logging stubs.** Deliberate, per rule 5 — and the single most expensive thing in this layer. **A stub that returns zero is not safe when zero is a meaningful answer**, and the list of ways that bit is now long enough to be a rule rather than an anecdote: | stub | what zero meant | what it looked like | |---|---|---| | `memcpy` | the copy did not happen | frames arrived as the right *length* of zeroes | | `_find_next_bit` | "bit 0 is set" | `for_each_cpu` never terminated; `ndo_open` hung | | `netif_carrier_off` | the carrier is already up | driver skipped its link-up path; `TCTL.EN` never set | | `__x86_indirect_thunk_r8` | the jump was discarded | 255 receive buffers requested, none allocated, `RDT` at 0 | | `dma_map_page_attrs` | bus address 0 | the NIC pointed at the bottom of physical memory | Not one of these reported an error, and only the last is a fault waiting to happen. A search function, a predicate, a jump and an address are all things for which zero is a specific answer rather than an absent one.