ACPI, DMI, SMP, xHCI, USB, I2C, NVMe, r8169 and ramdisk progress lines are
kinfo now: in dmesg and on a verbose boot, off the screen of a working
machine. Failures stay cprintf.
vt_repaint also paints the strip right of the last column and below the
last row, which kept the bottom of the X desktop after Ctrl+Alt+F-key.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S1giNvrHTrPMPw7V6x1kQ4
The touchpad driver crashed the ASUS TUF A15 at boot. Its thread runs the
firmware's AML -- _DSM, _PS0, _CRS -- through uACPI at -O0, on an 8 KB
kernel stack, and kernel stacks are one array: running off the end lands
in the next thread's stack, and the machine dies a moment later in some
other code. The thread now runs on a 64 KB stack of its own, through
SCFF's call_on_stack().
And a crashed laptop sat with its fans up until somebody held the power
button, since the other processors keep running. On an ordinary boot the
PSOGM now says it will power off, and does, after three minutes: SLP_TYP
from \_S5, read at boot, written straight to PM1 control with no AML, which
could sleep or wait on a lock a dead processor holds. A verbose boot keeps
the screen up for ever.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S1giNvrHTrPMPw7V6x1kQ4
Sixty-five headers sat side by side in include/, so `#include "irq.h"`
said nothing about where irq.h was or what it belonged to, and errno.h,
stat.h and fcntl.h at the top shadowed the system's for any host tool
built with -I./include. They are in folders now -- arch/ core/ fs/
dev/ gfx/ net/ uapi/ (and ldls/ for the Linux driver layer) -- and
every include names the folder, as Linux's do: "core/proc.h".
Done mechanically and checked the hard way: the kernel built from this
tree disassembles identically to the one built from the tree before
it. The full image boots, and userland is the same set of programs.
Paths in docs and comments follow; docs/guides/layout.md has a table
of what is where, and tools/fix-includes.py rewrites old-style
includes from the folders in the tree, for code written before this.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S1giNvrHTrPMPw7V6x1kQ4
The filesystem every other system can read: a USB stick, an SD card, the
EFI system partition. It is here first for the hardware report, which has
to leave a machine on something that can be read on another one.
mount -t vfat /dev/usb0p1 /mnt (msdos and fat work too; -o ro)
Written from Microsoft's specification, and matched to Linux vfat where
the specification leaves a choice: 8.3 names with the NT lowercase bits,
long-name entries otherwise, Linux's alias rule (REPORTS, then BIGNUM~1),
case-insensitive lookup, UTC times, the boot-sector dirty bit, every FAT
copy and FSInfo kept up to date. It uses its own sector cache over the
new blkdev_xfer, since a partition need not be a whole number of 4 KB
blocks, and every operation that changes something reaches the disk
before it returns. Inode numbers come from the entry position, or the
first cluster for a directory, plus a small table for entries that moved.
Around it:
- /dev lists every disk and partition the block layer found (major 8,
minor = block device), and raw reads and writes on them go by sector.
- The ESP and MBR FAT partitions are registered, typed so the root probe
passes over them. MBR entries with a bad status byte are skipped, so a
superfloppy's boot code is not read as a partition table.
- statfs, sync, fsync, umount (EBUSY while in use), shutdown, reboot and
the power button all know about FAT.
- create undoes and reports a failed ialloc or dirlink (ENOSPC, EINVAL,
EPERM) instead of panicking; fs_ops gains refuse_types and no_hardlinks.
- filewrite returns a short write instead of panicking on it.
- utimensat is implemented. As a stub returning 0 it made toybox touch
believe the file existed, so `touch newfile` created nothing on any
filesystem.
Tested in QEMU against mkfs.vfat images (FAT12 floppy, FAT16 on MBR,
FAT32 superfloppy and GPT ESP) by writing, renaming, deleting, filling to
ENOSPC and truncating there, then checking with fsck.fat -n and mtools on
the host: all clean, contents match.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S1giNvrHTrPMPw7V6x1kQ4
"acpi: 0 PCI interrupts routed through _PRT" on an AMD board meant that
every PCIe bridge's devices are wired to the second I/O APIC, which is not
driven. It says so now, and that those devices need MSI.
"vga: framebuffer disagreement" on an NVIDIA card compared the GOP's
framebuffer against BAR0, a 16 MB register block big enough to pass for a
screen. The BAR that contains the framebuffer is preferred now.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S1giNvrHTrPMPw7V6x1kQ4
The firmware's AML is now interpreted. uACPI 6.1.1 (MIT) is fetched by
ports/uacpi, checksum-verified, and compiled into the kernel unmodified,
the same way lwIP is. kernel/acpi/host.c is its host layer: memory,
mapping, port and PCI config I/O, time, mutexes and events that spin
before the scheduler exists, the SCI, and an "acpi" thread for the
work the SCI defers.
PCI interrupts go where the board says. pci_init() now routes every
device's INTx through the root bridge's _PRT before drivers bind. It
follows link devices' _CRS, uses a bridge's own _PRT where the namespace
has one, and swizzles through bridges that don't. Before this, INTx
waited on the 8259's line number, which is the wrong pin in APIC mode.
irq_register() takes a trigger mode rather than a level/low flag,
because q35's links and most SCIs are level, active-high. The MADT's
interrupt source overrides are now parsed, and are what places the SCI.
The power button syncs the filesystems and powers off. shutdown() and
reboot() go through the firmware's S5 and reset register first, and
only then fall back to the emulators' ports, which a real board does
not answer.
Tested under QEMU: q35 with MSI off routes xHCI to GSI 22,
level/active-high, and it takes real interrupts with nothing polled.
system_powerdown powers off q35 and i440fx (QEMU exits 0), and q35
with 4 CPUs boots from NVMe with USB hot-plug working alongside.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S1giNvrHTrPMPw7V6x1kQ4
