Symlinks are followed in namex_from() now, in the middle of a path as
well as at the end, and a relative target resolves from the directory
that holds the link rather than from the caller's cwd. `ln -s f d1/s;
cat d1/s` said "Symbolic link loop" because it looked for ./f. A loop is
ELOOP after 40 links, a dangling link ENOENT, and open(O_CREAT) through
a link to a file opens the file. divesymlink() is gone.
mknod from a Linux program passes (mode, dev) where the native call
passes (major, minor), and was read as the native one: `mknod n c 1 2`
made node 432,258, and mkfifo made a character device. Both are decoded
now; a FIFO is EPERM, and an existing name is EEXIST.
/proc/mounts listed devtmpfs twice: once from a fixed line and once
from the mount table. The fixed line is gone, and mount_add() refuses
a filesystem mounted on its own root, which is where a second devtmpfs
mount lands. A read-only FAT mount says ro.
/proc/partitions exists, in Linux's format, and /proc/filesystems lists
vfat.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S1giNvrHTrPMPw7V6x1kQ4
The filesystem every other system can read: a USB stick, an SD card, the
EFI system partition. It is here first for the hardware report, which has
to leave a machine on something that can be read on another one.
mount -t vfat /dev/usb0p1 /mnt (msdos and fat work too; -o ro)
Written from Microsoft's specification, and matched to Linux vfat where
the specification leaves a choice: 8.3 names with the NT lowercase bits,
long-name entries otherwise, Linux's alias rule (REPORTS, then BIGNUM~1),
case-insensitive lookup, UTC times, the boot-sector dirty bit, every FAT
copy and FSInfo kept up to date. It uses its own sector cache over the
new blkdev_xfer, since a partition need not be a whole number of 4 KB
blocks, and every operation that changes something reaches the disk
before it returns. Inode numbers come from the entry position, or the
first cluster for a directory, plus a small table for entries that moved.
Around it:
- /dev lists every disk and partition the block layer found (major 8,
minor = block device), and raw reads and writes on them go by sector.
- The ESP and MBR FAT partitions are registered, typed so the root probe
passes over them. MBR entries with a bad status byte are skipped, so a
superfloppy's boot code is not read as a partition table.
- statfs, sync, fsync, umount (EBUSY while in use), shutdown, reboot and
the power button all know about FAT.
- create undoes and reports a failed ialloc or dirlink (ENOSPC, EINVAL,
EPERM) instead of panicking; fs_ops gains refuse_types and no_hardlinks.
- filewrite returns a short write instead of panicking on it.
- utimensat is implemented. As a stub returning 0 it made toybox touch
believe the file existed, so `touch newfile` created nothing on any
filesystem.
Tested in QEMU against mkfs.vfat images (FAT12 floppy, FAT16 on MBR,
FAT32 superfloppy and GPT ESP) by writing, renaming, deleting, filling to
ENOSPC and truncating there, then checking with fsck.fat -n and mtools on
the host: all clean, contents match.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S1giNvrHTrPMPw7V6x1kQ4
Devices can now arrive and leave after boot. A "usbhotplug" kernel thread
handles root-port changes, which it is told about by Port Status Change
events and also checks for every quarter second. It also handles changes
behind hubs, which each hub reports on its status-change endpoint. An
unplugged device has its endpoints closed and any transfer in flight
failed. Then its drivers' disconnect hooks run, the slot is disabled and
its memory is freed. Everything behind a hub that goes goes with it. This
needed the interrupt handler to file command and endpoint-0 completions
for their waiters, so that enumeration can run while keyboards interrupt.
On real hardware: the controller is taken from the firmware through USB
Legacy Support before reset, with SMIs off. On Intel 7/8/9 series parts
the ports are switched over from EHCI, which is where firmware leaves
them.
Every interface of a device is offered to the class drivers, not just
the first, so a receiver's mouse on interface 1 gets a driver. Configure
Endpoint now copies the slot context from the controller. Before, it
rebuilt it and lost the route string and TT fields of devices behind
hubs.
HID: pointers are read in report protocol from their report descriptor.
That covers buttons, X/Y and wheel, relative or absolute, and report IDs.
Boot protocol is kept as the fallback for mice and for keyboards.
Non-pointer HID interfaces are declined rather than treated as tablets.
USB keyboards get software key repeat. Mass storage handles up to four
sticks, each unregistered from the block layer when it is pulled out,
along with its cached blocks.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HH7xukt4aaiGj1nQEAoQf1
q35 stopped with "no root filesystem" because its disk is SATA, like
every PC since 2008, and SchOS only had IDE. And SchFS could only sit
on a whole raw device, so nothing could boot from a disk that also
carried an ESP.
- include/blkdev.h, kernel/dev/blkdev.c: a registry of block devices
found at probe time, numbered from 4. A disk's GPT (or MBR) is read
when it registers, and each partition becomes a device whose block 0
is the partition's first sector. SchFS needs no format change to live
in a partition; a Linux SchFS driver will see the same bytes on
/dev/sdX2. SchFS has its own GPT type:
47138FA9-B79C-47A6-9F7D-AC1F7F572D5E.
- AHCI driver, written from the AHCI 1.3.1 spec: BIOS handoff,
COMRESET when the link is down, IDENTIFY, 48-bit DMA read/write,
FLUSH. Completion is polled, so the root disk does not depend on
interrupt routing.
- USB sticks also register as usb0, so their partitions are found.
- The root probe tries registered devices between USB and IDE,
SchFS-typed partitions first.
- make disk / tools/posix/mkdisk.sh: a GPT image with a 64 MB ESP and
a SchFS partition, ready to dd to a stick or a disk.
Tested in QEMU q35: the old two-disk setup roots on sata1; disk.img as
the only SATA disk roots on sata0p2; disk.img as a USB stick (firmware
boots from it) roots on usb0p2. Writes survive sync in each case.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HH7xukt4aaiGj1nQEAoQf1
