Sixty-five headers sat side by side in include/, so `#include "irq.h"`
said nothing about where irq.h was or what it belonged to, and errno.h,
stat.h and fcntl.h at the top shadowed the system's for any host tool
built with -I./include. They are in folders now -- arch/ core/ fs/
dev/ gfx/ net/ uapi/ (and ldls/ for the Linux driver layer) -- and
every include names the folder, as Linux's do: "core/proc.h".
Done mechanically and checked the hard way: the kernel built from this
tree disassembles identically to the one built from the tree before
it. The full image boots, and userland is the same set of programs.
Paths in docs and comments follow; docs/guides/layout.md has a table
of what is where, and tools/fix-includes.py rewrites old-style
includes from the folders in the tree, for code written before this.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S1giNvrHTrPMPw7V6x1kQ4
A native driver written from the NVMe 1.4 base specification. It resets
the controller the firmware left running, then sets up an admin queue and
one I/O queue pair. Completion is polled, with interrupts disabled at the
queue, for the same reason AHCI polls: without AML, interrupt routing on
real hardware cannot be trusted. Each active namespace with 512-byte to
4 KB sectors and no metadata is registered as nvme<C>n<N>, the name
Linux uses, and its GPT is read like any other disk's.
Tested under QEMU q35: disk.img on NVMe as the only disk boots through
OVMF, roots on nvme0n1p2, and writes read back after sync. A
4 KB-sector namespace registers.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S1giNvrHTrPMPw7V6x1kQ4
/proc/interrupts on q35 said "LOSING 526" ticks: 5 s of boot with
interrupts off. Timing each step of kmain() found two waits:
- AHCI sent a COMRESET to every empty port and waited a second for a
link. DET = 0 is "no device", so only DET = 1 is worth a reset now
(after 20 ms of grace for a drive that is still spinning up).
- ideinit() read 0xFF from a bus with no IDE controller, took the BSY
bit for a busy drive, and waited out its 1 s timeout. A status of
0xFF means no controller and is answered at once.
That is every PC with SATA disks. q35 now loses 33 ticks, under the
flag; i440fx still roots on IDE and loses none.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HH7xukt4aaiGj1nQEAoQf1
q35 stopped with "no root filesystem" because its disk is SATA, like
every PC since 2008, and SchOS only had IDE. And SchFS could only sit
on a whole raw device, so nothing could boot from a disk that also
carried an ESP.
- include/blkdev.h, kernel/dev/blkdev.c: a registry of block devices
found at probe time, numbered from 4. A disk's GPT (or MBR) is read
when it registers, and each partition becomes a device whose block 0
is the partition's first sector. SchFS needs no format change to live
in a partition; a Linux SchFS driver will see the same bytes on
/dev/sdX2. SchFS has its own GPT type:
47138FA9-B79C-47A6-9F7D-AC1F7F572D5E.
- AHCI driver, written from the AHCI 1.3.1 spec: BIOS handoff,
COMRESET when the link is down, IDENTIFY, 48-bit DMA read/write,
FLUSH. Completion is polled, so the root disk does not depend on
interrupt routing.
- USB sticks also register as usb0, so their partitions are found.
- The root probe tries registered devices between USB and IDE,
SchFS-typed partitions first.
- make disk / tools/posix/mkdisk.sh: a GPT image with a 64 MB ESP and
a SchFS partition, ready to dd to a stick or a disk.
Tested in QEMU q35: the old two-disk setup roots on sata1; disk.img as
the only SATA disk roots on sata0p2; disk.img as a USB stick (firmware
boots from it) roots on usb0p2. Writes survive sync in each case.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HH7xukt4aaiGj1nQEAoQf1
