SchOS/kernel/dev/ide.c

// Simple PIO-based (non-DMA) IDE driver code.

#include "types.h"
#include "defs.h"
#include "irq.h"
#include "param.h"
#include "memlayout.h"
#include "mmu.h"
#include "proc.h"
#include "x86.h"
#include "traps.h"
#include "spinlock.h"
#include "sleeplock.h"
#include "fs.h"
#include "buf.h"

#define SECTOR_SIZE   512
#define IDE_BSY       0x80
#define IDE_DRDY      0x40
#define IDE_DF        0x20
#define IDE_ERR       0x01

#define IDE_CMD_READ  0x20
#define IDE_CMD_WRITE 0x30
#define IDE_CMD_RDMUL 0xc4
#define IDE_CMD_SETMULT 0xc6
#define IDE_CMD_WRMUL 0xc5
// The 48-bit forms. Same operations, an address that is not capped at 128 GB.
#define IDE_CMD_READ_EXT  0x24
#define IDE_CMD_WRITE_EXT 0x34
#define IDE_CMD_RDMUL_EXT 0x29
#define IDE_CMD_WRMUL_EXT 0x39
// FLUSH CACHE, and the form a drive using 48-bit addressing wants. Neither
// takes an address; the difference is only which one a given drive admits to
// supporting, so ideflush tries the plain one and falls back.
#define IDE_CMD_FLUSH     0xe7
#define IDE_CMD_FLUSH_EXT 0xea

// idequeue points to the buf now being read/written to the disk.
// idequeue->qnext points to the next buf to be processed.
// You must hold idelock while manipulating queue.

static struct spinlock idelock;
static struct buf *idequeue;

static int havedisk0;
static int havedisk1;
static void idestart(struct buf*);

// Wait for the drive to become ready, or give up.
//
// This used to be an unbounded `while`. On a machine with nothing attached to
// the primary channel the status register reads 0xFF forever, so the very
// first call from ideinit() hung the kernel -- no panic, no message, just a
// dead machine right after the VGA banner. That is not an exotic
// configuration: it is every CD boot, and most hardware newer than IDE.
//
// The bound is deliberately enormous. A real drive answers in microseconds;
// this only expires when there is nothing there at all.
static int
idewait(int checkerr)
{
  int r = 0;

  for(int i = 0; i < 20000000; i++){
    r = inb(0x1f7);
    if((r & (IDE_BSY|IDE_DRDY)) == IDE_DRDY){
      if(checkerr && (r & (IDE_DF|IDE_ERR)) != 0)
        return -1;
      return 0;
    }
  }
  return -1;
}

static void
ide_irq(void *arg)
{
  (void)arg;
  ideintr();
}

// SET MULTIPLE MODE: how many sectors the drive moves per interrupt during
// READ/WRITE MULTIPLE. Must equal BSIZE/SECTOR_SIZE or idestart()'s single
// insl/outsl of a whole block does not line up with the drive's bursts.
//
// A drive may refuse a count it cannot do (IDENTIFY word 47 carries its
// maximum; QEMU allows 16). If it does, say so rather than continue: the
// transfers would silently desynchronise, which reads as filesystem
// corruption rather than as a driver problem.
static void
ide_set_multiple(int dev)
{
  int spb = BSIZE / SECTOR_SIZE;

  outb(0x1f6, 0xe0 | ((dev & 1) << 4));
  if(idewait(0) < 0)
    return;
  outb(0x1f2, spb);
  outb(0x1f7, IDE_CMD_SETMULT);
  if(idewait(1) < 0)
    cprintf("ide%d: SET MULTIPLE MODE %d rejected; expect trouble\n", dev, spb);
}

void
ideinit(void)
{
  initlock(&idelock, "ide");
  // ISA signalling: edge-triggered, active high. Everything at a fixed
  // legacy port is wired this way; PCI devices are not.
  irq_register(IRQ_IDE, ide_irq, 0, "ide", 0);

  // A timeout here means there is no drive on this channel. Say so and leave
  // havedisk0/1 clear: with a ramdisk root there is nothing else the system
  // needs from IDE, and booting on is strictly better than stopping.
  if(idewait(0) < 0){
    cprintf("ide: no drive on the primary channel\n");
    return;
  }
  havedisk0 = 1;

  // Check if disk 1 is present
  outb(0x1f6, 0xe0 | (1<<4));
  for(int i=0; i<1000; i++){
    if(inb(0x1f7) != 0){
      havedisk1 = 1;
      break;
    }
  }

  // Tell each drive how many sectors to move per interrupt.
  //
  // READ/WRITE MULTIPLE transfer the drive's *multiple count* of sectors
  // between interrupts, and that count is whatever SET MULTIPLE MODE last
  // established -- it is not taken from the sector-count register. Nothing
  // ever issued it here, so the count was undefined, which is the real reason
  // idestart() carried a `sector_per_block > 7` panic: BSIZE was 1024, two
  // sectors, and nobody had tested further.
  //
  // Establishing it explicitly is what lets BSIZE be a whole SchFS block. At
  // 1024 every 4096-byte SchFS block cost four IDE requests, each with its own
  // interrupt and sleep/wakeup, and exec() of the 800 KB toybox binary meant
  // ~800 round trips -- about two seconds, on every command.
  ide_set_multiple(0);
  if(havedisk1)
    ide_set_multiple(1);

  // Switch back to disk 0.
  outb(0x1f6, 0xe0 | (0<<4));
}

// Is there actually a drive there? Callers that probe -- rather than callers
// that know what they are looking for -- have to ask, because reading an
// absent drive is a bug and iderw() treats it as one.
int
ide_disk_present(int dev)
{
  return dev == 0 ? havedisk0 : havedisk1;
}

// Start the request for b.  Caller must hold idelock.
static void
idestart(struct buf *b)
{
  if(b == 0)
    panic("idestart");

  // No FSSIZE check. It used to panic on any block past 150000 -- 614 MB at
  // BSIZE -- which is a constant describing the *v1 filesystem image*, not the
  // disk. It had no business bounding a device, and it was the lowest ceiling
  // in the stack by three orders of magnitude: the format addresses 64 ZB and
  // the drive was refused past half a gigabyte.
  int sector_per_block = BSIZE/SECTOR_SIZE;
  uint64 sector = b->blockno * (uint64)sector_per_block;

  // No `sector_per_block > 7` panic here any more. That limit existed because
  // nothing had set the drive's multiple count, so anything past the tested
  // two sectors was a guess; ideinit() issues SET MULTIPLE MODE now, and the
  // count is whatever BSIZE says.

  // LBA28 addresses 2^28 sectors, which is 128 GB and no more. Past that the
  // 48-bit commands are the only way to name the sector at all, so the mode is
  // chosen per request: LBA28 stays the path for everything that fits, because
  // it is the one every existing image has been read through.
  int lba48 = sector >= (1ULL << 28);
  int read_cmd, write_cmd;

  if(lba48){
    read_cmd  = (sector_per_block == 1) ? IDE_CMD_READ_EXT  : IDE_CMD_RDMUL_EXT;
    write_cmd = (sector_per_block == 1) ? IDE_CMD_WRITE_EXT : IDE_CMD_WRMUL_EXT;
  } else {
    read_cmd  = (sector_per_block == 1) ? IDE_CMD_READ  : IDE_CMD_RDMUL;
    write_cmd = (sector_per_block == 1) ? IDE_CMD_WRITE : IDE_CMD_WRMUL;
  }

  idewait(0);
  outb(0x3f6, 0);  // generate interrupt

  if(lba48){
    // The high half goes first, then the low half into the same registers:
    // each is a two-deep FIFO, and writing them in the other order leaves the
    // drive addressing whichever sector the low bytes alone describe.
    outb(0x1f2, 0);                          // sector count, high byte
    outb(0x1f3, (sector >> 24) & 0xff);
    outb(0x1f4, (sector >> 32) & 0xff);
    outb(0x1f5, (sector >> 40) & 0xff);
    outb(0x1f2, sector_per_block);           // sector count, low byte
    outb(0x1f3, sector & 0xff);
    outb(0x1f4, (sector >> 8) & 0xff);
    outb(0x1f5, (sector >> 16) & 0xff);
    // LBA48 carries no address bits in the drive/head register.
    outb(0x1f6, 0x40 | ((b->dev&1)<<4));
  } else {
    outb(0x1f2, sector_per_block);
    outb(0x1f3, sector & 0xff);
    outb(0x1f4, (sector >> 8) & 0xff);
    outb(0x1f5, (sector >> 16) & 0xff);
    outb(0x1f6, 0xe0 | ((b->dev&1)<<4) | ((sector>>24)&0x0f));
  }

  if(b->flags & B_DIRTY){
    outb(0x1f7, write_cmd);
    outsl(0x1f0, b->data, BSIZE/4);
  } else {
    outb(0x1f7, read_cmd);
  }
}

// Interrupt handler.
void
ideintr(void)
{
  struct buf *b;

  // First queued buffer is the active request.
  acquire(&idelock);
  if((b = idequeue) == 0){
    release(&idelock);
    // cprintf("spurious IDE interrupt\n");
    return;
  }
  idequeue = b->qnext;

  // Read data if needed.
  if(!(b->flags & B_DIRTY) && idewait(1) >= 0)
    insl(0x1f0, b->data, BSIZE/4);

  // Wake process waiting for this buf.
  b->flags |= B_VALID;
  b->flags &= ~B_DIRTY;
  wakeup(b);

  // Start disk on next buf in queue.
  if(idequeue != 0)
    idestart(idequeue);
  else
    wakeup(&idequeue);          // ideflush waits for the channel to go quiet

  release(&idelock);
}

// FLUSH CACHE: do not return until the drive has committed what it has taken
// to the medium.
//
// Every layer above this driver assumes a write that has returned is on the
// disk. On a drive with a volatile write cache that is simply not true, and it
// is the assumption SchFS's whole crash-safety argument rests on: copy-on-write
// promises that a crash lands on either the old tree or the new one, but only
// if the tree blocks reach the platter before the uberblock that names them.
// The drive is otherwise free to write them in whatever order suits its head,
// and a power cut then leaves a newest uberblock -- correctly checksummed --
// pointing at a tree that was never written. Nothing can recover from that,
// because nothing about it looks wrong.
//
// Polled rather than queued: it moves no data, so it does not fit idestart's
// shape, and it is rare enough that the simplest correct thing wins.
int
ideflush(int dev)
{
  int r = 0;

  if(dev == 0 ? !havedisk0 : !havedisk1)
    return 0;                   // nothing there is nothing to flush

  acquire(&idelock);

  // The channel has to be idle. This talks straight to the registers, and
  // issuing it underneath a queued transfer would corrupt that transfer's
  // handshake rather than merely delay it.
  while(idequeue != 0)
    sleep(&idequeue, &idelock);

  outb(0x3f6, 2);               // nIEN: this command answers by status, not IRQ
  outb(0x1f6, 0xe0 | ((dev & 1) << 4));
  if(idewait(0) < 0){
    r = -1;
    goto out;
  }

  outb(0x1f7, IDE_CMD_FLUSH);
  // A drive with a full write cache can take seconds over this, which is the
  // other reason idewait's bound is as large as it is.
  if(idewait(1) < 0){
    // Drives that came up in 48-bit mode may abort the 28-bit spelling. Same
    // operation, and there is no third option, so a failure here is real.
    outb(0x1f7, IDE_CMD_FLUSH_EXT);
    if(idewait(1) < 0){
      cprintf("ide%d: FLUSH CACHE failed; writes are not durable\n", dev);
      r = -1;
    }
  }

out:
  outb(0x3f6, 0);               // interrupts back on for ordinary transfers
  release(&idelock);
  return r;
}

//PAGEBREAK!
// Sync buf with disk.
// If B_DIRTY is set, write buf to disk, clear B_DIRTY, set B_VALID.
// Else if B_VALID is not set, read buf from disk, set B_VALID.
void
iderw(struct buf *b)
{
  struct buf **pp;

  if(!holdingsleep(&b->lock))
    panic("iderw: buf not locked");
  if((b->flags & (B_VALID|B_DIRTY)) == B_VALID)
    panic("iderw: nothing to do");
  if(b->dev != 0 && !havedisk1)
    panic("iderw: ide disk 1 not present");
  if(b->dev == 0 && !havedisk0)
    panic("iderw: ide disk 0 not present");

  acquire(&idelock);  //DOC:acquire-lock

  // Append b to idequeue.
  b->qnext = 0;
  for(pp=&idequeue; *pp; pp=&(*pp)->qnext)  //DOC:insert-queue
    ;
  *pp = b;

  // Start disk if necessary.
  if(idequeue == b)
    idestart(b);

  // Wait for request to finish.
  while((b->flags & (B_VALID|B_DIRTY)) != B_VALID){
    sleep(b, &idelock);
  }

  release(&idelock);
}